HACKRF ONE SERIAL NUMBER
HACKRF ONE INSTALL
HACKRF ONE DRIVERS
HACKRF ONE PLUS

HACKRF ONE PLUS

I have successfully tested Orange Pi PC2 H5 and Orange PI One Plus H6 for SSB reception and SSB transmission.ItвЂ™s time to thin the herd! Over the coming weeks, IвЂ™m planning to liquidateВ some gearВ here at the SWLing Post HQ. We are going to move towards 64-bit 4-core processors like the H5 or the H6. We forget the Orange Pi Zero which, following the treatment defined in GNU-RADIO, quickly risks running out of power.

To use it, the Orange Pi solution is very interesting. The HackRF being developed in Open Source can be bought in China at Aliexpress for a hundred Euros. With the rtl_eeprom -h command, we have the corresponding help. You can reprogram this number by typing: rtl_eeprom -s 'numГ©ro de sГ©rie'

HACKRF ONE SERIAL NUMBER

The difficulty with RTL-SDRs is that they all carry the serial number 1 when they are manufactured. For a hackrf type in a terminal hackrf_info and retrieve the serial number and put it in the вЂDevice ArgumentsвЂ™ box. In the case of several SDRs connected to the processing card, they must be identified. If you observe no further output, everything is fine. Info: This tool will continuously read from the device, and report if You can get the available gain values provided that the RTL-SDR was not started by an application. Only the RF gain parameter acts on the RTL-SDR. In general, expect less gain at higher frequencies. They nominally provide 14 dB of gainВ when on, but the actual amount of gain varies by frequency. In the off state, the amps are completely bypassed. The RX and TX, RF amplifiers have two settings: on or off. baseband (вЂњvgaвЂќ, 0 to 62 dB in 2 dB steps).RX : three different analog gainВ controls.For the gains, it is necessary to make tests to find the good values according to the model of SDR. It is not necessary to identify the SDR if only one is connected to the processing board. To enter data from HackRF One or RTL-SDR, use the Osmocom source module in GNU-Radio.

HACKRF ONE INSTALL

Sudo apt install lxterminal Osmocom module If you have when launching a model in gnuradio companion a message of the type Xterm executable is missing and if you are on Armbian or Raspbian (raspberry) go to the configuration folder.ДЇirst of all, check that the terminal is installed on your machine. On a terminal in graphics mode type:ДЄ message вЂњRANDRвЂќ missing вЂ¦ is not important. I connect to them by enabling VNC in setup and using the VNC extension in chrome on my PC. Personally, I use my orange-pi or raspberry in remote mode. You have to be in graphics mode to be able to use this superb signal processing design tool.

S udo ldconfig Osmocom source module installation DINSTALL_UDEV_RULES=ON -DDETACH_KERNEL_DRIVER=ONДЄt this point I sometimes got an error because the pkg-config package was not found. We clone Osmocom in the userвЂ™s Downloads folder for example: Sudo apt-get install cmake build-essential libusb-1.0-0-dev

HACKRF ONE DRIVERS

Sudo apt-get install gnuradio Installation Osmocom SDR and RTL-SDR Drivers RTL-SDR and Orange PI One Plus

So far for Debian Buster there is only version 3.7.13 which is considered stable. GNU Radio Companion is a complementary tool allowing to build radio processing chains graphically without writing a line of code. GNU Radio is a very powerful tool for modelling signal processing chains. If the installation is good, you will get a response вЂњFound HackRFвЂќ etc вЂ¦ Sometimes with some USB cables that connect the HackRF, there is no response. HackRF LibraryД¬onnect the hackrf to an USB port and check it: Connection of the HackRF One SDR to an Orange Pi Pc2 or Orange PI One Plus running on ARMBIAN or a Radpberry PI. Here we will discuss the connection of these 2 SDRs to an Orange Pi or a Raspberry PI and their operation with the GNU Radio software. RTL-SDR is the cheapest and most well-known SDR working in reception only. HackRF One is an SDR (Software Defined radio) working in transmission and reception in a wide frequency range.

Hackrf one